×
Animation for G5456
×
Your Cart ×
Estimated Total: Checkout Now
Item #: G5456
Model # G5456

SUPERCUT G5456 - 85" x 3/4" x .035" x 6-10 TPI VP Bi-Metal Bandsaw Blade

Bi-Metal Bandsaw blade sized to fit the G4030 6-1/2" x 10" Metal Cutting Bandsaw.

Specifications:

Length: 85"

Width: 3/4"

TPI: 6-10 VP

Gauge: .035"

If you need more information to help match blade lengths and widths to your particular applications, just call our friendly service technicians.

Blade Selection: Selecting the right blade for the cutting task requires knowledge about bl... View More Details

$5195
+$000 Freight
+$000  Oversize
Add to Cart
Available to Ship
Add to Cart

Overview
Bi-Metal Bandsaw blade sized to fit the G4030 6-1/2" x 10" Metal Cutting Bandsaw.

Specifications:

  • Length: 85"
  • Width: 3/4"
  • TPI: 6-10 VP
  • Gauge: .035"

If you need more information to help match blade lengths and widths to your particular applications, just call our friendly service technicians.

Blade Selection: Selecting the right blade for the cutting task requires knowledge about blade characteristics and cutting priorities (i.e. speed, finish, etc.).

  • Blade Length: Measured by the blade circumference, blade lengths are specific to each bandsaw. They are determined by the wheel diameter and distance between the wheels.
  • Blade Width: Measured from the back of the blade to the tip of the blade tooth (the widest point). Blade width determines the largest and smallest curve that can be cut, and contributes to the accuracy of cutting straight—generally the wider the blade, the straighter it will cut.

    Tooth Set: Two common tooth sets for wood bandsaw blades are alternate and raker. Each type of tooth set removes material in a different manner, leaving cuts with different characteristics.

  • Alternate: An all-purpose arrangement where the teeth are bent evenly left and right of the blade.
  • Raker: Three teeth in a recurring group—one bent left, one bent right, and one that is not bent. The raker set is ideal for most contour cuts.

    Tooth Type: The most common tooth types for wood blades are:

  • Standard (or Raker): Equally spaced teeth set at a “0” rake angle. Recommended for thinner workpieces and general use.
  • Hook (or Claw): Wide gullets (round or flat), equally spaced teeth, positive rake angle, and fast cut with good surface finish.
  • Skip (or Skip Tooth): Wide, flat gullets, a "0" rake angle, equally spaced teeth, and recommended for thick wood cutting.
  • Reviews

    3 Customer Reviews (5 out of 5 stars) : Sign in to write a review

    Anonymous Reviewer
    03/09/2019 1:42:26 AM

    No feedback given

    Anonymous Reviewer
    Bi-Metal Bandsaw Bades are the only blades I will buy. 02/08/2018 2:07:55 PM

    I have cut what seems like miles of low carbon steel with these bi-metal blades. After several months the weld usually fatigues and I replace the blade, but I cut up the old blade for hacksaw blades as the teeth are still sharp! I have tried several carbon steel blades, and have the opposite experience, they seem to dull within a few cutting hours. Spend the extra money for the bi-metal blade, to save money and frustration in the long run.

    Anonymous Reviewer
    Yes I love this blade it was just what I needed 06/21/2017 3:06:06 PM

    Yes I needed a corse blade o ordered a 6-10 TPI VP
    G5456 blade to fit my new Grizzly G4030 bandsaw
    Which I love it is the perfect saw for my shop
    I needed to cut some 1" and some 2" thick HRS brackets. I could have used a little bit coarser blade
    Like the 5-8 TPI VP G5455 but the 6-10 worked just fine for this thick steel . It just took a little longer I think
    But on the other hand it was better getting through
    The torch burns . Which I had to go through a lot
    Of it . I made three of these brackets .